Musical Instruments and Sound Equipment: Online Music Store >> Applied Microphone Technology
Applied Microphone TechnologyBuy Applied Microphone Technology musical instruments and sound equipment online at lowest price. Applied Microphone Technology AMT HR2 Clip On Harmonica Condenser Microphone and other Applied Microphone Technology products for sale.  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT HR2 Clip On Harmonica Condenser Microphone. The AMT HR-2 mic is a clip-on version of the AMT HR1 hand held microphone system for harmonica. The system is low in profile, which allows it to be used with a standard neck harness. The microphone comes with clips to attach to the harmonica. The AMT HR2 is the only microphone on the market that can be used in combination with a harmonica neck brace.The AMT HR2 can be used with most major brand wireless belt pack transmitters and receivers. With the AMT Interface, the microphone can plug directly into the interface which then plugs directly into most major brand wireless units. When ordering the AMT Interface, be sure to know your wireless make, model, and pin out configuration. Interfaces are made to order.Allows use with 9V battery or phantom power — battery preferred.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT Z1 Clip On Condenser Microphone. The AMT Z1 is a hardwired single microphone made for flute. The Z1 mic is the perfect choice from soft to louder playing applications. It can be used for featured soloist to miking a section of flutes. The AMT Z1 single microphone gets the most gain before feedback. The system comes with the microphone, special low mass flute clamp and preamp. The preamp uses the chip technology which contours the microphone for the most natural reproduction of sound possible. Perfect for all situations. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT WSW Clip On Double Cond Mic for Shure Systems. The AMT WSW - Shure is a special version of the AMT WS. The microphone element remains with the same high level of quality that the WS achieves however is specially adapted to work with any Shure belt pack transmitter/wireless system such as the ULXS14 or ULXP14. The WS comes wired directly with a 4 pin connector to connect directly to any Shure wireless belt pack.The WS is a low profile double condenser microphone that attaches to the clarinet, alto and bass flute, or oboe with a ultra-miniature low mass clamp. It is specifically designed for the timbre of the clarinet. The microphone provides pure tonal reproduction while being unobtrusive. It has an even reproduction of sound across the entire instrument. The AMT WS features a flexible gooseneck, allowing the player to position the microphone for the best possible tone reproduction. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive. The WSW features one microphone at the bell and second positioned over the keys to provide a truer reproduction for the musical instrument's tone quality. The AMT WSW mic also comes with two isolation rings. Both microphones are suspended in AMT's iso-ring technology which allows more gain before feedback and less handling noise. A low Z cable and case is included.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT WS Studio Clip On Double Cond Mic Sys. The AMT WS Studio version combines the AMT WS Clip-On Double Microphone system with the AMT AP40 floor pre-amp. The AP40 converts the microphones to low impedance, it regulates the voltage to each microphone, and with certain models creates a specific frequency curve. The curve is necessary on certain models or musical instruments in order to maintain the most natural reproduction of sound in conjunction with achieving the most amount of gain before feedback in a live application. The output of the preamp is an XLR Low Impedance balanced output. The output sends signal at Mic Level. The AMT WS is a low profile double condenser microphone system that attaches to the clarinet, alto and bass flute, or oboe with a ultra-miniature low mass clamp. It is specifically designed for the timbre of the clarinet. The microphone provides pure tonal reproduction while being unobtrusive. It has an even reproduction of sound across the entire instrument. The AMT WS features a flexible gooseneck, allowing the player to position the microphone for the best possible tone reproduction. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive. The AMT WS Studio comes with two isolation rings. Both instrument microphones are suspended in AMT's iso-ring technology which allows more gain before feedback and less handling noise. The AMT WS Studio version is meant to be used either in a Studio setting where close miking of an musical instrument is desired or in a professional level setting where the sound engineer needs control of the microphone.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT TA2 Low Profile Clip On Double Cond Mic. The AMT TA2 is a low profile double condenser microphone that attaches to the bell with a low mass clip specifically designed soprano or baritone saxophone. The microphone provides pure tonal reproduction while being unobtrusive. The TA2 is an excellent choice for a principal artist or soloist.The first microphone attaches to the bell of the saxaphone, the second or over-the-keys microphone is suspended in a 4 point isolation ring reducing valve, key, click, and handling noise. Both microphones are on goosenecks for optimal placement. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive.The AMT TA2 mic is terminated by a 3.5mm plug which connects to a belt pack preamp. The output is a pre-determined mix balanced at AMT's state of the art facility. The engineers choose the balance by the natural sound of the instrument. The included belt pack houses a volume control, contours the setup for the intended instrument, and powers the microphone system appropriately. A low Z cable and case is included.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT TA2 Studio Clip On Double Cond Mic Sys. The AMT TA2 Studio Clip-On Double Microphone System includes two AMT TA2 low profile condenser microphones and the AMT AP40 Preamp. The AMT TA2 is a low profile double condenser microphone that attaches to the bell with a low mass clip specifically designed soprano or baritone saxophone. The TA2 microphone provides pure tonal reproduction while being unobtrusive. It's an excellent choice for a principal artist or soloist.The microphone attaches to the bell of instrument, the top or over the keys microphone is suspended in a 4 point isolation ring reducing valve, key, click, and handling noise. The second microphone is placed in front of the bell of the microphone. Both microphones are on goosenecks for optimal placement. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive.The AP40 Preamp converts all of the microphones to low impedance, it regulates the voltage to each microphone, and with certain models creates a specific frequency curve. The curve is necessary on certain models or musical instruments in order to maintain the most natural reproduction of sound in conjunction with achieving the most amount of gain before feedback in a live application. There is a L / G switch on the preamp. This is a Ground Lift switch. If phantom power is not regulated for the correct voltage OR if phantom is reduced by the addition / amount of other condenser microphone connected, the switch disconnects the phantom power and allows it's own battery supply to power the preamp. If the switch is moved to the L position, the preamp is powered by the battery. If the switch is in the G position, phantom will power the preamp. The output of the preamp is an XLR Low Impedance balanced output.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT LS Studio Low Profile Clip On Cond Mic System. The AMT LS is the ultimate in a woodwind or brass microphone. The system is meant to clip onto any flanged bell instrument (Saxophones and Brass). The LS in it's stock configuration is the perfect choice for the player that needs control of there volume in a belt pack style setup. The latest version of the AMT LS allows the player to easily change to and from AMT different preamps and allows for direct connections to either Shure or Sennheiser beltpack transmitters. With a change in a cable, convert your LS mic from a beltpack style preamp, to a "Studio" series model, and then to AMT "Wireless setups". The instrument microphone is suspended in a 4 point isolation ring reducing key and handling noise. Phantom power or 9Volt battery required. Comes with BP40 beltpack style preamp, case, and AMT disconnecting cable technology to allow the microphone to be used as "Wireless" or "Studio" models if needed. (Additional cables for a variety of setups sold separately. AMT Interface also sold separately to allow connections for many wireless systems).. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT LSW Clip On Cond Mic for Sennheiser Systems. The AMT LSW — Sennheiser Microphone System is a special version of the AMT LS. It is meant to be used by the player that requires a multi-channel professional level wireless system. The microphone element remains the same with the same high level of quality that the LS achieves however is specially adapted to work in this Sennheiser configuration. The AMT system is meant to clip onto a flanged bell instrument. (Saxophones and Brass) and was designed for direct connection to Sennheiser belt pack wireless systems.The AMT LSW allows the brass instrument player to easily convert their direct connecting wireless microphone to any AMT preamp version. With a change in a cable, you can convert your LS from a "W"ireless setup, to a "Belt pack", or the AMT "Studio" series. The microphone is suspended in a 4 point isolation ring reducing key and handling noise. It is powered via the wireless belt pack. This system comes with microphone, universal clamp, case, and AMT disconnecting cable technology to allow the microphone to be used as "W"ireless or "BP" models if needed. (Additional cables for a variety of setups sold separately. The AMT Interface is also sold separately to allow connections for many wireless systems). Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT VS Low Profile Clip On Condenser Microphone. The AMT VS Microphone System includes the AMT VS Clip-On condenser microphone and the AMT belt pack preamp. The VS is a ultra miniature, feather weight low profile condenser microphone specially designed for the violin, viola, and mandolin. The microphone attaches to the violin, viola, and mandolin with a clamp designed for be solid on the instrument without harming or dampening the natural sound or vibrations. The microphone provides pure tonal reproduction while being unobtrusive. The reproduction of natural sound of the instrument is the goal. Includes a hardshell Blo-mold protective case and " to XLR cable.The AMT VS can be used with most major brand wireless belt pack transmitters and receivers. With the AMT Interface, the microphone can plug directly into the interface which then plugs directly into most major brand wireless units. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT VS Studio Low Profile Clip On Cond Mic Sys. The AMT VS Studio version combines the natural AMT VS Studio Clip-On microphone system with the AMT AP40 floor pre-amp. The AP40 converts the microphones to low impedance, it regulates the voltage to each microphone, and with certain models creates a specific frequency curve. The curve is necessary on certain models or instruments in order to maintain the most natural reproduction of sound in conjunction with achieving the most amount of gain before feedback in a live application. The output of the preamp is an XLR Low Impedance balanced output. The output sends signal at Mic Level. The AMT VS Studio version is meant to be used either in a studio setting where close miking of an instrument is desired OR in a professional level setting where the sound engineer needs control of the microphone. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT VSW Clip On Cond Mic for Sennheiser Systems. The AMT VSW - Sennheiser Clip-On Condenser Microphone System was designed to operate with Sennheiser wireless systems. The VS is a ultra miniature, feather weight low profile condenser microphone specially designed for the violin, viola, and mandolin. The microphone attaches to the violin, viola, and mandolin with a clamp designed for be solid on the instrument without harming or dampening the natural sound or vibrations. The VSW instrument microphone provides pure tonal reproduction without being unobtrusive. With the included AMT Interface, the microphone can plug directly into the interface which then plugs directly into Sennheiser wireless units. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT VSW Clip On Cond Mic for Shure Systems. The AMT VSW - Shure Clip-On Condenser Microphone System was designed to operate with Shure wireless systems. The VS is an ultra miniature, feather-weight, low-profile condenser microphone specially designed for the violin, viola, and mandolin. The AMT mic attaches firmly to instrument with a clamp designed to not harm it or dampen its natural sound or vibrations. The clip on microphone provides pure tonal reproduction without being obtrusive. With the included AMT Interface, the microphone can plug directly into the interface which then plugs directly into Shure wireless transmitter. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT WS Low Profile Clip On Double Cond Mic. The AMT WS Clip-On Double Microphone System includes the WS Double condenser microphone and the BP40 Belt pack Preamp. The WS is a low profile double condenser microphone that attaches to the clarinet, alto and bass flute, or oboe with a Ultra- miniature low mass clamp. It is specifically designed for the timbre of the clarinet, The instrument microphone provides pure tonal reproduction while being unobtrusive. It has an even reproduction of sound across the entire instrument. The AMT WS features a flexible gooseneck, allowing the player to position the microphone for the best possible tone reproduction. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive. The WS features one microphone at the bell and second positioned over the keys to provide a truer reproduction for the musical instrument's tone quality.The WS mic is terminated by a 3.5mm plug which connects to a belt pack preamp. The output is a predetermined mix balanced by the nature of the instrument. The included belt pack houses a volume control, contours the setup for the intended instrument, and powers the microphone system appropriately. A low Z cable and case is included.The AMT WS models including WSW, WS Studio, and the WS all come with TWO isolation rings now. Both microphones are suspended in AMT's iso-ring technology which allows more gain before feedback and less handling noise. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT LS Low Profile Clip On Condenser Microphone. The AMT LS is the ultimate in a woodwind or brass microphone. The system is meant to clip onto a flanged bell instrument (Saxophones and Brass). The LS mic in its stock configuration is the perfect choice for the player that needs control of their own volume in a belt pack style setup. The AMT LS also allows the player to easily change to and from AMT different preamps and allows for direct connections to either Shure or Sennheiser beltpack transmitters. With a change in a cable, convert your LS from a beltpack style preamp, to a "Studio" series model, and then to AMT "Wireless setups". The microphone is suspended in a 4 point isolation ring reducing key and handling noise. Phantom power or 9Volt battery required. The instrument mic comes with BP40 beltpack style preamp, case, and AMT disconnecting cable technology to allow the microphone to be used as "Wireless" or "Studio" models if needed. (Additional cables for a variety of setups sold separately. AMT Interface also sold separately to allow connections for many wireless systems).. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT Z1W Clip On Cond Mic for Shure Systems. The AMT Z1W - Shure is a special version of the AMT Z1 flute microphone designed to work with any Shure belt pack transmitter/wireless system such as the ULXS14 and the ULXP14. The Z1 flute microphone comes wired directly with a 4-pin connector to connect directly to any Shure wireless belt pack. The Z1 is the perfect choice from soft to louder playing applications. It can be used for featured soloist or for miking a section of flutes. It provides excellent gain before feedback and includes a special low-mass flute clamp. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT LSW Clip On Cond Mic for Shure Systems. The AMT LSW Clip On Condenser Microphone is the ultimate in a woodwind or brass microphone and designed for direct connection to Shure or Sabine belt pack wireless systems. The mic system is meant to clip onto a flanged bell instrument. (Saxophones and Brass). The AMT LSW — Shure Microphone System is meant to be used by the player that requires a multi-channel professional level wireless system. (AMT Recommends the Shure ULXS14 and the ULXP14 wireless units). The AMT LSW allows the player to easily convert their direct connecting wireless microphone to any AMT preamp version. With a change in a cable, you can convert your LS from a "W"ireless setup, to a "Belt pack", or the AMT "Studio" series. The microphone is suspended in a 4 point isolation ring reducing key and handling noise. It is powered via the wireless beltpack. This LSW system comes with microphone, universal clamp, case, and AMT disconnecting cable technology to allow the microphone to be used as "W"ireless or "BP" models if needed. (Additional cables for a variety of setups sold separately. The AMT Interface is also sold separately to allow connections for many wireless mic systems). Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT M40 Acoustic Piano Microphone System. The AMT M40 Acoustic Piano Microphone System is a bold new direction for microphones incorporating integrated circuit technology, an interchangeable chip which allows for multi-purpose use, and emulates many popular microphones with the advantages of its ultra compact size. The M40 Acoustic Microphone System includes the AMT M40 Microphone and the AP 40 Floor Preamp. The M40 Microphone system lets you reproduce the natural sound of the piano. Mono in design, the system allows for use even with the piano lid closed. It is capable of picking up subtle passages as well as sound pressure levels up to 141dB. The M40 microphone's signal can be split and frequencies rolled off in a specific way to create a stereo image. The M40 Piano Microphone System features rugged construction of anodized aviation aluminum allowing it to withstand high impact while being lightweight and non-corrosive. The M40 has been designed for piano but works equally well in other applications such as boundary layer miking (conference, stage). The M-40 terminates to the AP 40 aluminum preamp with chip technology and can be powered by phantom power or 9v battery. Includes a hardshell Blo-mold protective case.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT 350 Large Diaphragm Condenser Microphone. The AMT 350 large diaphragm studio microphone is designed to record vocals and instruments on classic analog and the popular growing digital format. With a cardioid pattern, the 350 mic is designed to be used in front of guitar cabinets, acoustic guitars, vocals, and acoustic instruments. The AMT 350 incorporates an element nearly an inch in diameter with a thickness of 6 microns of gold on the diaphragm which gives it it's wide frequency range and stellar sensitivity.The AMT 350 is engineered to capture the most natural sound from the source in a controlled setting and was after the most expensive European large diaphragm microphones with emphasis on the sonic quality instead of additional features. The 350 has transparent and high definition detail down to subtle sonic qualities. The 350 mic is in an affordable price range allowing one to purchase in pairs for stereo overhead use as well. It's ultra low noise level allows it to compete with any studio microphone on the market. Comes complete with hard shell case and clip for mounting to a microphone stand. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT M51 Bass Drum Microphone System. The AMT M51 mic has been designed for bass drum but works equally well in other applications such as boundary layer miking (conference, stage). The M51 is a bold direction for microphones incorporating integrated circuit technology, an interchangeable chip which allows for multi-purpose use, and emulates many popular microphones with the advantages of its ultra compact size. It is capable of picking up subtle passages as well as sound pressure levels up to 141dB. Its rugged construction of anodized aviation aluminum allows it to withstand high impact while being lightweight and non-corrosive. The AMT M-51 Bass Drum Mic is terminated with an XLR connector and includes a cast aluminum pre-amp which can be powered by phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT SP25B Acoustic Bass Condenser Microphone. The SP25B is an electret-condenser microphone that has been designed for acoustic bass. All of the parameters that are problematic for the double bass have been addressed. To be able to get the most gain before feedback it uses a very tight pattern to give a high rejection to surrounding noise, at the same time reproducing accurately the subtleties of the bass. As placement is especially important with an instrument that has a fine finish and varying dimensions, this microphone's attachment mechanism is designed to secure the mic to the bass in different positions taking seconds to attach. This mechanism is fitted with natural soft suede so as not to mark or mar instrument.The SP25B uses the "super pre-amp" which has 2 XLR outputs, one of which has a ground lifted isolation transformer split. A quarter inch line driver output with volume control is also included. The pre-amp runs off of battery, phantom power, or optional power supply. However it is recommended using the 9-volt battery all the time. The line driver and isolation transformer will not work unless you have a 9-volt battery in the pre-amp. The external volume control is for the line driver/1/4 inch output. The preamp also has an internal volume control that you can adjust with a screw driverMade from aluminum to keep the mass low yet extremely strong, this microphone will remain durable through many years of use. The flex arm is easy to position yet retains it's placement throughout the most active of performances. The mic has an LED that can be easily seen while performing. This indicates status of a battery or phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT Z1 Studio Clip On Condenser Microphone System. The AMT Z1 Studio version combines the smallest and only specific flute microphone system on the market with the AMT AP40 floor preamp. The AP40 converts the microphones to low impedance. It regulates the voltage to each microphone, and with certain models creates a specific frequency curve. The curve is necessary on certain models or instruments in order to maintain the most natural reproduction of sound and the most gain before feedback in a live applications. An XLR low-impedance balanced output sends a mic level signal. The AMT Z1 is a hardwired single microphone made for flute. It is the perfect choice for soft or louder playing applications. It can be used for featured soloist or miking a section of flutes. This studio version is meant to be used either in a studio setting where close miking of an instrument is desired or in a professionalsetting where a sound engineer controls the microphone.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT VP3 Mallet Percussion Microphone System. The AMT VP3 Mallet Percussion Microphone System is a three microphone setup for vibraphone and other mallet instruments. Endorsed by Dave Samuels and Tony Miceli, the VP3 microphone is a unique approach to miking that allows the closest placement of mics and lets the player, audience, and engineer hear the true acoustic sound of the instrument. Its quick and easy setup and tear down make it also easy to travel with. The VP3 has two microphones placed over the top of the instrument and the third placed under. Can be adjusted by clamp and a flexible gooseneck. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT S15G Studio Low Profile Clip On Cond Mic Sys. The AMT S15G Studio version combines the AMT S15G cardioid guitar microphone system with the AMT AP40 floor preamp. The AP40 converts the microphones to low impedance, it regulates the voltage to each microphone, and with certain models creates a specific frequency curve. The curve is necessary is on certain models or musical instruments in order to maintain the most natural reproduction of sound in conjunction with the achieving the most amount of gain before feedback in a live application. The output of the preamp is an XLR low-impedance balanced outputThe S15G comes with a cable that disconnects as well. This cable will allow the player to switch back and forth between the different AMT preamps as well as convert it to the "Wireless" setup. (Different cables and preamps sold separately)The AMT S15G Studio version is meant to be used either in a studio setting where close miking of an instrument is desired or in a professional level setting where the "Sound Engineer" controls the microphone.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT 404 Small Diaphragm Condenser Microphone Pair. The AMT 404 Small Diaphragm Condenser Microphone Pair have a cardioid polar pattern and are designed for live sound reinforcement and studio applications. The 404's can withstand high sound pressure levels (SPL) and have an extended frequency response.The AMT 404 microphone pair is suitable for many applications including the overhead miking of musical instruments as well as choirs, speech, and vocalist of all types. The 404 pair is ideal for home recording applications and studios when a stereo setup is required. Engineered with the same natural qualities of all the AMT microphones the 404's include a hard shell carrying case and microphone clips for mounting on mic stands. The AMT 404 operates on phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Instrument Wireless Systems > Applied Microphone Technology Wi-5 Instrument Wireless System. The AMT Wi-5 complete wireless microphone system is the ultimate wireless microphone for professional-grade woodwind and brass instruments. Based on AMT's Roam 1 Elite, the Wi-5 is the next generation in belt pack-free wireless technology. The Wi-5 is a multi-channel (16 selectable), belt pack-free wireless system. Special modifications have been set in place in order to acheive AMT's best setup to date. AMT has addressed all crucial issues that one would search for when shopping for a high-end instrument microphone. Common concerns such as gain before feedback, frequency response, and keeping the most accurate and natural sound possible are once again present on the Wi-5 system. The AMT Wi-5 comes complete with the microphone accented in blue and suspended in AMT Iso-ring technology, a 16-channel AMT wireless transmitter attached to the microphone, AMT's Universal Clamp, a receiver with XLR, 1/4" outputs, and a power supply.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT P800 Studio Low Profile Clip On Cond Mic Sys. The AMT P800 Studio microphone system combines the most natural sounding trumpet specific microphone system on the market with the AMT AP40 floor pre-amp. The AP40 converts the microphones to low impedance, it regulates the voltage to each microphone, and with certain models creates a specific frequency curve. The curve is necessary on certain models or instruments in order to maintain the most natural reproduction of sound in conjunction with achieving the most amount of gain before feedback in a live application. The output of the preamp is an XLR Low Impedance balanced output. The output sends signal at Mic Level.The AMT P800 Studio Trumpet microphone system features an element somewhere in size between a small and large diaphragm, which prevents even the loudest of trumpet players to not overload the microphone. AMT has developed their special "Off the bell" clamping system for this model which clamps to the mouthpipe of the trumpet or flugelhorn. The AMT P800 microphone allows the player to easily change to and from AMT different preamps and allows for direct connections to either Shure or Sennheiser beltpack transmitters. With a change in a cable, convert your P800 from a "Studio" style preamp, to a "Belt pack" series model, or to the AMT "W"ireless setups. The microphone is suspended in a 4 point isolation ring reducing key and handling noise. Phantom power or 9Volt battery required. Comes with AP40 floor or "DI" style preamp, hardshell case, and AMT disconnecting cable technology to allow the microphone to be used as "Wireless" or "BP" models if needed. (Additional cables for a variety of setups sold separately. The AMT Interface is also sold separately to allow connections for many wireless systems.). ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT P800 Low Profile Clip On Condenser Microphone. The AMT P800 Trumpet microphone system is the only system on the market specifically made to handle the highest SPL levels that a trumpet reproduces. The AMT P800 microphone system features an element somewhere in size between a small and large diaphragm, which prevents even the loudest of trumpet players to not overload the microphone. AMT has developed their special "Off the bell" clamping system for this model which clamps to the mouthpipe of the trumpet or flugelhorn. The AMT P800 allows the player to easily change to and from AMT different preamps and allows for direct connections to either Shure or Sennheiser belt pack transmitters. With a change in a cable, convert your P800 trumpet mic from a beltpack style preamp, to a "Studio" series model, and then to AMT "W"ireless setups. The microphone is suspended in a 4 point isolation ring reducing key and handling noise. Phantom power or 9-Volt battery is required. Comes with AP40 floor or "DI" style preamp, hardshell case, and AMT disconnecting cable technology to allow the microphone to be used as "Wireless" or "BP" models if needed. (Additional cables for a variety of setups sold separately. The AMT Interface is also sold separately to allow connections for many wireless systems.). ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT TA2W Double Cond Mic for Sennheiser Systems. The AMT TA2W - Sennheiser is a low profile double condenser microphone system designed to work with Sennheiser Wireless Systems. The first microphone attaches to the bell of the musical instrument, the top or over the keys microphone is suspended in a 4 point isolation ring reducing valve, key, click, and handling noise. The second microphone is placed in front of the bell of the microphone. Both TA2W microphones are on goosenecks for optimal placement. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive.The AMT interface lets the artist use AMT microphones with most Sennheiser wireless transmitters. In most cases the interface will eliminate the beltpack that has come with your microphone system. The AMT Interface will replace the belt pack and can be fastened using velcro to the belt pack of whichever wireless system that you are using. With the AMT Interface, the microphone can plug directly into the interface which then plugs directly into most major brand wireless units. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT TA2W Double Cond Mic for Shure Systems. The AMT TA2W — Shure is a low profile double condenser microphone System designed to work with Shure Wireless Systems. The first microphone attaches to the bell of instrument, the top or over the keys microphone is suspended in a 4 point isolation ring reducing valve, key, click, and handling noise. The second microphone is placed in front of the bell of the microphone. Both microphones are on goosenecks for optimal placement. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive.The AMT interface lets the artist use AMT microphones with most Shure wireless transmitters. In most cases the Interface will eliminate the beltpack that has come with your microphone system. The AMT Interface will replace the belt pack and can be fastened using velcro to the belt pack of whichever wireless system that you are using. With the AMT Interface, the microphone can plug directly into the interface which then plugs directly into most major brand wireless units. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT P800W Clip On Cond Mic for Sennheiser Systems. The AMT P800W — Sennheiser is a special version of the AMT P800W. The microphone element remains the same with the same high level of quality that the P800 achieves however is specially adapted to work in a Sennheiser configuration. The AMT P800 Trumpet microphone system is the only system on the market specifically made to handle the highest SPL levels that a trumpet can reproduce. The AMT P800 microphone system features an element somewhere in size between a small and large diaphragm, which prevents even the loudest of trumpet players to not overload the microphone. AMT has developed there special "Off the bell" clamping system for this model which clamps to the mouthpipe of the trumpet or flugelhorn. The AMT — Sennheiser allows the player to easily convert their directly connecting wireless microphone to any AMT preamp version. With a change in a cable, convert your P800W from a "W"ireless setup, to a "Belt pack", or the AMT "Studio" series. The microphone is suspended in a 4 point isolation ring reducing key and handling noise. Phantom power or 9-Volt battery is required. Comes with AP40 floor or "DI" style preamp, hardshell case, and AMT disconnecting cable technology to allow the microphone to be used as "Wireless" or "BP" models if needed. (Additional cables for a variety of setups sold separately. The AMT Interface is also sold separately to allow connections for many wireless systems.). ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT P800W Clip On Cond Mic for Shure Systems. The AMT P800W trumpet microphone is a special version of the AMT P800. The microphone element remains the same with the same high level of quality that the P800 achieves however is specially adapted to work in this Shure configuration. AMT recommends the Shure ULXS14 and the ULXP14 Wireless Units. The AMT P800W - Shure Microphone System is meant to be used by the player that requires a mult-channel professional level wireless system. This application is a commonly preferred method used by many professional level sound engineers as well as sound companies on major tours.The AMT P800 Trumpet microphone system is the only system on the market specifically made to handle the highest SPL levels that a trumpet can reproduce. The AMT P800 microphone system features an element somewhere in size between a small and large diaphragm, which prevents even the loudest of trumpet players to not overload the microphone. AMT has developed there special "Off the bell" clamping system for this model which clamps to the mouthpipe of the trumpet or flugelhorn.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT S15G Low Profile Clip On Condenser Microphone. The S15G is a low-profile condenser microphone that has a cardioid pattern which gives it better gain before feedback than most guitar microphones on the market. The element as well as the mounting clamp is designed for the instrument. AMT designs microphones for each instrument and does NOT adapt elements or mounting gear to fit instruments. The S15G system clamps to the outside of the guitar. It is adjustable from a minimum of 3" to a maximum of 5-7/8". The AMT S15G features a flexible 6" gooseneck, allowing the player to position the microphone for the best possible tone reproduction. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive.The microphone attaches to the side of the guitar or other musical instrument, and is suspended in a 4 point isolation ring reducing handling noise. The S15G terminates to the BP42 belt pack. It operates on either 9 volt battery or Phantom power to 48 volts DC. It incorporates an LED to indicate the status of the voltage.The S15G is terminated by a 3.5mm plug which connects to a belt pack preamp. The included belt pack houses a volume control, contours the setup for the intended instrument, and powers the microphone system appropriately. A low Z cable and case is included.The S15G instrument mic also comes with a cable that disconnects. This cable will allow the player to switch back and forth between the different AMT Preamps as well as convert it to the wireless setup. (Different cables and preamps sold separately). ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology AMT Z1W Clip On Cond Mic for Sennheiser Systems. Applied Microphone Technology's special version of the AMT Z1 flute microphone is designed to work with any Sennheiser transmitter/wireless system. The Z1W flute microphone comes wired directly with a 4-pin connector to connect directly to any Sennhieser wireless mic belt pack. The AMT Z1 is a hardwired single microphone made for flute. The Z1W is the perfect choice from soft to louder playing applications. It can be used for featured soloist to miking a section of flutes. The AMT Z1 single microphone gets the most gain before feedback. The system comes with the microphone, special low-mass clamp, and preamp. The preamp uses the chip technology which contours the microphone for the most natural reproduction of sound possible.Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT S18C Cello Condenser Microphone. The S18C is an electret-condenser microphone that has been designed for cello. All of the mic'ing parameters that are problematic for string instruments have been addressed. To be able to get the most gain before feedback it uses a very tight pattern to give a high rejection to surrounding noise, at the same time reproducing accurately the subtleties of the cello. As placement is especially important with an instrument that has a fine finish and varying dimensions, this microphone's attachment mechanism is designed to secure the mic to the cello in different positions taking seconds to attach. This mechanism is fitted with natural soft suede so as not to mark or mar instrument.Made from aluminum to keep the mass low yet extremely strong, this microphone will remain durable through many years of use. The flex arm is easy to position yet retains it's placement throughout the most active of performances. The mic has an LED that can be easily seen while performing. This indicates status of a battery or phantom power. The pre-amp for the microphone is rugged anodized aviation aluminum, which houses the electronics that can be placed on the floor. This pre-amp utilizes a circuit that can change EQ, curve, and gain by exchanging EPROM-like chip. The preamp runs off of battery or phantom power. The output is terminated with a male XLR type connector for balanced use. The mic is connected to the preamp by a 4-pin locking connector.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT S25B Acoustic Bass Condenser Microphone. The S25B is an electret-condenser microphone that has been designed for acoustic bass. All of the parameters that are problematic for the double bass have been addressed. To be able to get the most gain before feedback it uses a very tight pattern to give a high rejection to surrounding noise, at the same time reproducing accurately the subtleties of the bass. As placement is especially important with an instrument that has a fine finish and varying dimensions, the S25B microphone's attachment mechanism is designed to secure the mic to the bass in different positions taking seconds to attach. This mechanism is fitted with natural soft suede so as not to mark or mar instrument. Made from aluminum to keep the mass low yet extremely strong, this AMT microphone will remain durable through many years of use. The flex arm is easy to position yet retains it's placement throughout the most active of performances. The mic has an LED that can be easily seen while performing. This indicates status of a battery or phantom power. The preamp for the S25B microphone is rugged anodized aviation aluminum, which houses the electronics that can be placed on the floor. This preamp utilizes a circuit that can change EQ, curve, and gain by exchanging EPROM-like chip. The preamp runs off battery or phantom power. The output is terminated with a male XLR type connector for balanced use. The mic is connected to the preamp by a 4-pin locking connector.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT S3G Studio Low Profile Clip On Cond Mic Sys. The AMT S3G Studio version combines AMT's Omni Guitar specific microphone system with the AMT AP40 floor pre-amp. The AP40 converts the microphones to low impedance, it regulates the voltage to each microphone, and creates a specific frequency curve in order to maintain the most natural reproduction of sound in conjunction with the achieving the most amount of gain before feedback in a live application. The output of the preamp is an XLR Low Impedance balanced output. The AMT S3G Studio version is meant to be used either in a studio setting where close miking of an instrument is desired or in a professional level setting where the "Sound Engineer" needs control of the microphone. The S3G Studio is a unique, low-profile condenser microphone that can only be used with an acoustic guitar that has a sound-hole under the strings. This microphone incorporates an omni pattern to capture the sound from inside the guitar. The S3G Studio Mic features a flexible gooseneck, allowing the player or sound engineer to position the microphone for the best possible tone reproduction. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive. Requires phantom power.. ...details  Applied Microphone Technology Pro Audio > Microphones > Condenser Microphones > Applied Microphone Technology AMT System 1 Low Profile Clip On Cond Mic Sys. The AMT System 1 is a low profile condenser microphone that attaches to the bell of any flanged bell instrument such as horns, woodwind and brass, with a low mass clip. It can also clamp to many other musical instruments using the AMT "Universal Clamp". The microphone provides pure tonal reproduction while being unobtrusive. The System 1 microphone element is designed to be used with 40 or more instruments. It's response is designed to complement everything from brass and woodwinds to percussion. See the list below of all possible instruments to use it on.With the included clip portion of the "Universal Clamp", the System 1 microphone can be used on soprano, alto, tenor and bari sax, as well as trumpet, trombone, baritone horn, flugelhorn and tuba. The clip portion of the "Universal Clamp" is used for flanged bell instruments such as brass and woodwinds. It is a spring loaded design with a set screw that can reinforce stability on the horn if the player needs. The microphone attaches to the bell of the instrument, and is suspended in a 4 point isolation ring reducing valve, key, click, and handling noise.The AMT System 1 features a flexible gooseneck, allowing the player to position the microphone for the best possible tone reproduction. It's rugged construction of anodized aviation aluminum makes it highly durable, while being lightweight and non-corrosive.The System 1 instrument mic is terminated by a 3.5mm plug which connects to a special metal belt pack preamp. The included belt pack has an XLR output. It is power by either 1 AA battery or phantom power. The belt pack powers the microphone system appropriately and needs to be used.. ...details  Applied Microphone Technology Pro Audio > Microphones > Percussion Microphones > Applied Microphone Technology ERTS Percusssion Microphone. The AMT ERTS is a 2nd generation microphone system for drums and percussion instruments designed, hand-manufactured, and distributed by Applied Microphone Technology in the USA. Its mini condenser microphone features natural and even sound reproduction, resistance to feedback, and high SPL tolerances, making it perfect for professional live and studio use. The mic system comes with 1 AMT microphone with Iso-Ring technology, an AMT inline preamp (phantom power required), and a clamp that fits onto various drums and percussion instruments. It can even attach to the ropes of hand drums.The ERTS incorporates a flat frequency response, allowing the microphone to reproduce percussion instruments as naturally as possible. The inline preamp can be placed on the floor, a belt clip for mobility, or in your pocket. A low roll-off filter and a dB cut are included on the inline preamp.. ...details Applied Microphone Technology Pro Audio > Microphones > Specialty Microphones > Applied Microphone Technology HR3 Harmonica Microphone. The AMT HR3 is Applied Microphone Technology's 3rd generation of harmonica microphone systems. It's designed and manufactured by hand in the USA to reproduce the sound of the harmonica as naturally as possible. The HR3 microphone is intended to fit different-sized harmonicas from diatonic to 16-hole. The HR3, unlike its predecessors, has a clamp that adjusts by a thumb and allen screw to fit different instruments. The HR3 mic also includes AMT's DCT (Disconnecting Cable Technology), allowing for easy replacement of the cable from the harmonica microphone and giving it the ability to interface with various wireless systems on the market.The included AMT inline preamp can be used on the floor, with a belt clip, or in a pocket, and it has a low roll-off filter as well as a dB cut. The system includes a soft carrying pouch, AMT inline preamp (phantom power required), and adjustable clamp.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Wireless System Components > Applied Microphone Technology Wi5G Guitar Wireless Transmitter. The AMT Wi5G Guitar Wireless System is a removable 16-selectable-channel wireless setup. The Wi5G is intended to work with all types of electric guitars, allowing players to perform wirelessly without being tied down to a belt pack or cables of any type. The Wi5G features a plug-and-play-style transmitter that is very light in weight and delivers exceptional sound clarity and wireless reception. The most impressive feature of AMT's wireless mic system is its ability to convert and adapt to all AMT microphones. The Wi5G transmitter, after unplugging the included 1/4" adapter from your guitar, can then plug directly into any AMT microphone with D.C.T. (Disconnect Cable Technology), giving you an acoustic mic setup. Along with the ability to switch between 16 channels, this versatility makes the Wi5G an invaluable tool for guitar players. The Wi5G wireless transmitter features an on/off and mute switch along with a Gain adjustment. An LED indicates on/off status and low battery. One AAA battery is needed to power the transmitter. Designed to be used with either pedals or an acoustic guitar, the receiver comes with both a 1/3" and XLR output. The AMT Wi5G works with all types of electric guitars as well as AMT microphone models: LS, WS, TA2, Z1, P800, M40, S15G, VS, S25B, and the S18C. Microphones sold separately.. ...details  Applied Microphone Technology Pro Audio > Wireless Systems > Instrument Wireless Systems > Applied Microphone Technology Wi5C Clip-On Wireless Transmitter Black. The Applied Microphone Wi5C is a removable wireless clip-on transmitter and receiver with 16 selectable channels. The system currently works in conjunction with all AMT microphone systems that have disconnecting cable technology. Applied Microphone Technology's new disconnecting cables allow you to use their AMT microphone in many applications. AMT microphones can be ordered with beltpack-style preamps, studio or DI-style preamps, and the wireless direct connecting systems.You can use the Wi5C wireless transmitter in conjunction with several microphones and with the change of a cable, you can convert your microphone to either of the AMT preamps, or a wireless beltpack made by Shure, Sennheiser, and the new Wi5C wireless system. Microphone sold separately.Wi5C now works on these AMT models if they include a cable disconnect located on the microphone:Single microphone systems:LS, LS Studio, LSW - Shure, LSW - Sennheiser P800, P800 Studio, P800W - Shure, P800W - Sennheiser S15G, S15G Studio S25B, S25B-TP, SP25B, SP25B-TP M40, M51 ERT P43Double microphone systems:WS, WS Studio, WSW - Shure, WSW - Sennheiser TA2, TA2 Studio, TA2W - Shure, TA2W - Sennheiser. ...details Applied Microphone Technology Pro Audio > Microphones > Specialty Microphones > Applied Microphone Technology ACCX Accordion Microphone. The AMT ACCX is an external microphone system for accordion designed, manufactured by hand, and distributed by Applied Microphone Technology in the USA. The system features a 1-microphone setup with an external bracket that mounts via double-sided tape to the front or side of any size or type of accordion. The bracket then can be removed if not needed, since it mounts with high-capacity Velcro. The ACCX is a great mic setup for the accordion player looking for a high-quality external clip-on microphone that can withstand the high sound pressure level of a musette-tuned accordion. It can also handle SPLs from bellow shaking as well as pick up the most sensitive levels of a single reed soloist. The bracket can accept and mount up to 3 AMT microphones for different miking techniques around the accordion. The ACCX allows, if needed, the ability to place 2 accordion microphones in front of the instrument's grille for miking the right hand and reverse the direction for the third microphone to pick up the left hand or opposite side of an accordion. The ACCX kit includes 1 AMT microphone with Iso-ring technology along with the ACCX accordion clamp and 1 preamp needed to power the microphone. Additional accordion microphones can be purchased separately. The included inline preamp can be placed on the floor, on a belt clip, or in-pocket. The preamp has a low roll-off switch as well as a dB cut. Phantom power is needed to power it. The ACCX accordion mic system also includes a soft carrying pouch for the microphone.. ...details  Applied Microphone Technology Pro Audio > Microphones > Specialty Microphones > Applied Microphone Technology S25B-TP Tailpiece Acoustic Bass Mic. The AMT S25B-TP is an electret-condenser microphone system that has been designed for acoustic bass. The system has exactly the same sound characteristics and functions as the famed S25B, however the "TP "(tail piece) systems includes the ability to mount the mic on the tailpiece of an acoustic bass.All of the parameters that are problematic for the double bass have been addressed. The S25B- TP bass microphone will acquire the most gain before feedback by using a very tight pattern to give a high rejection to surrounding noise. At the same time, the system reproduces with great definition capturing all of the subtleties of the bass.As placement is especially important with an instrument that has a fine finish and varying dimensions, this microphone's attachment mechanism is designed to attach to the tailpiece of the acoustic bass guitar. This allows the instrument and the microphone to be placed back into a carrying case without having to remove the microphone from the body of the instrument. All of the bass microphones now also include D.C.T. (Disconnect Cable Technology). D.C.T. allows you to remove the cable from the microphone.Made from aluminum to keep the mass low yet extremely strong, the AMT bass mic will remain durable through many years of use. The flex arm is easy to position yet retains it's placement throughout the most active of performances. The preamp for the microphone is rugged anodized aviation aluminum, which houses the electronics that can be placed on the floor. This preamp uses a circuit that can change EQ, curve, and gain by exchanging EPROM-like chip. The preamp runs off of battery or phantom power. The output is terminated with a male XLR type connector for balanced use. The AMT bass mic is connected to the preamp by a 4-pin locking connector. The system includes 1 microphone, cable that disconnects from the microphone, the AP40 preamp, and a hardshell case.. ...details  Applied Microphone Technology Pro Audio > Microphones > Specialty Microphones > Applied Microphone Technology SP25B-TP Tailpiece Acoustic Bass Mic. The AMT SP25B-TP is an electret-condenser microphone system that has been designed for acoustic bass. The mic system has exactly the same sound characteristic and functions as the famed SP25B, however the "TP" (tail piece) systems includes the ability to mount to the tail piece of an acoustic bass. The system also comes with the Super Preamp. All of the parameters that are problematic for the double bass have been addressed. The AMT SP25B-TP will acquire the most gain before feedback by using a very tight pattern to give a high rejection to surrounding noise. At the same time, the system reproduces with great definition capturing all of the subtleties of the bass. As placement is especially important with an instrument that has a fine finish and varying dimensions, this microphone's attachment mechanism is designed to attach to the tailpiece of the instrument. This allows the instrument and the microphone to be placed back into a carrying case without having to remove the microphone from the body of the instrument. This AMT microphone also features D.C.T. (Disconnect Cable Technology). D.C.T. allows you to remove and replace the cable from the microphone. Made from aluminum to keep the mass low yet extremely strong, the SP25B mic will remain durable through many years of use. The flex arm is easy to position yet retains it's placement throughout the most active of performances. Made from aluminum to keep the mass low yet extremely strong, this microphone will remain durable through many years of use. The Super preamp for this system is rugged and made of anodized aviation aluminum, which houses the electronics. The preamp can be placed on the floor and out of the way. This preamp uses a complex circuit that is tailored to the needs of an acoustic bass guitar player. The preamp runs off of 9-volt battery or phantom power. There are three outputs on a super preamp. One is terminated with a male XLR type connector for balanced use. The second output on a Super Preamp is a 1/4" "line driver" with a separate volume control for connecting to bass amps. Keep in mind that this system is a condenser microphone and intended to be used with equipment designed for microphones and not pickups. Depending on how your amp is manufactured you could have different results with a Super Preamp. Certain amps will work better than others with this system. All PA systems will work well. The third output is a ground lifted isolation split. The AMT mic is connected to the preamp by a four pin locking connector. The system comes with "SP" (Super Preamp) with 2 XLR Outputs, 1 1/4" inch line driver output, and a hardshell case.. ...details
|
|
|
|
|
|