GMS

GMS Drums and Percussion > Acoustic Drums > Floor Toms >

GMS Special Edition Floor Tom 16X18 Chestnut.

GMS Special Edition drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance in all dynamic situations with little to no distortion or necessity for reinforcement hoops, which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product.GMS Drum Co. is known for creating ingenious, yet functional, products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Floor Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell,a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. The toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.As for proper mounting, the Special Edition models employ the GMS Floor Tom Mounting System which spaces all the mounting hardware off the drum shell. With the wider circumference of the leg pattern, the drum shell is able to resonate without the restriction of mounting hardware against it. The mounting brackets themselves are even made at the GMS factory.As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.A lot goes into these GMS Special Edition Toms so you'll get a lot out of them as well. And by that we mean consistent. ...details

GMS Drums and Percussion > Acoustic Drums > Floor Toms >

GMS Special Edition Floor Tom 14X14 Chestnut.

GMS Special Edition drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance in all dynamic situations with little to no distortion or necessity for reinforcement hoops, which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product.GMS Drum Co. is known for creating ingenious, yet functional, products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Floor Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell,a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. The toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.As for proper mounting, the Special Edition models employ the GMS Floor Tom Mounting System which spaces all the mounting hardware off the drum shell. With the wider circumference of the leg pattern, the drum shell is able to resonate without the restriction of mounting hardware against it. The mounting brackets themselves are even made at the GMS factory.As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.A lot goes into these GMS Special Edition Toms so you'll get a lot out of them as well. And by that we mean consistent. ...details

GMS Drums and Percussion > Acoustic Drums > Floor Toms >

GMS Special Edition Floor Tom 16X16 Chestnut.

GMS Special Edition drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance in all dynamic situations with little to no distortion or necessity for reinforcement hoops, which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product.GMS Drum Co. is known for creating ingenious, yet functional, products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Floor Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell,a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. The toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.As for proper mounting, the Special Edition models employ the GMS Floor Tom Mounting System which spaces all the mounting hardware off the drum shell. With the wider circumference of the leg pattern, the drum shell is able to resonate without the restriction of mounting hardware against it. The mounting brackets themselves are even made at the GMS factory.As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.A lot goes into these GMS Special Edition Toms so you'll get a lot out of them as well. And by that we mean consistent. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Special Edition Snare Drum 7X13 Silver/Blue Sparkle Fade.

GMS snare drums use a throw-off and butt system on all that was designed by GMS and machined from brass. The unique nylon lock nut, prevents the throw-off adjusting knob from loosening, keeping GMS' promise to have a system that is simple, trouble-free, and effective. All GMS snare drums feature 20-strand, heat-treated, high-carbon steel snare wire. Hoops on all drums are 2.3mm steel triple flanged. All snare drums have coated Evans G1 tops, and 300-gauge snare bottoms.One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition snare sound.The GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product. GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.For snare with more fl. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS G28 Acrylic Snare Drum 6.5X14 Amber With Black.

The G28 Acrylic Snare drum from GMS is to regular snare drums like a formula one racing car is to your average commuter sedan. So it's little surprise that the acrylic shell is decked out with racing stripes. The drum's acrylic shell offers a brighter, louder voice in comparison to wood shell drums. The drum has an excellent crack with a medium-warm resonance.The drum's bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside. The throw-off and butt system was designed to be simple, trouble-free, and effective. The snare drum features 20 strand heat treated high carbon steel snare wire. Hoops are 2.3mm steel triple flanged. GMS acrylic snare drum ships with an Evans coated G1 top, and 300 gauge snare wire.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS G28 Acrylic Snare Drum 6.5X14 Ruby Red With White.

The G28 Acrylic Snare drum from GMS is to regular snare drums like a formula one racing car is to your average commuter sedan. So it's little surprise that the acrylic shell is decked out with racing stripes. The drum's acrylic shell offers a brighter, louder voice in comparison to wood shell drums. The drum has an excellent crack with a medium-warm resonance.The drum's bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside. The throw-off and butt system was designed to be simple, trouble-free, and effective. The snare drum features 20 strand heat treated high carbon steel snare wire. Hoops are 2.3mm steel triple flanged. GMS acrylic snare drum ships with an Evans coated G1 top, and 300 gauge snare wire.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS G28 Acrylic Snare Drum 6.5X14 Black With Silver.

The G28 Acrylic Snare drum from GMS is to regular snare drums like a formula one racing car is to your average commuter sedan. So it's little surprise that the acrylic shell is decked out with racing stripes. The drum's acrylic shell offers a brighter, louder voice in comparison to wood shell drums. The drum has an excellent crack with a medium-warm resonance.The drum's bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside. The throw-off and butt system was designed to be simple, trouble-free, and effective. The snare drum features 20 strand heat treated high carbon steel snare wire. Hoops are 2.3mm steel triple flanged. GMS acrylic snare drum ships with an Evans coated G1 top, and 300 gauge snare wire.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS G28 Acrylic Snare Drum 6.5X14 Dark Blue With White.

The G28 Acrylic Snare drum from GMS is to regular snare drums like a formula one racing car is to your average commuter sedan. So it's little surprise that the acrylic shell is decked out with racing stripes. The drum's acrylic shell offers a brighter, louder voice in comparison to wood shell drums. The drum has an excellent crack with a medium-warm resonance.The drum's bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside. The throw-off and butt system was designed to be simple, trouble-free, and effective. The snare drum features 20 strand heat treated high carbon steel snare wire. Hoops are 2.3mm steel triple flanged. GMS acrylic snare drum ships with an Evans coated G1 top, and 300 gauge snare wire.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Special Edition Snare Drum 6.5X14 Silver/Blue Sparkle Fade.

GMS snare drums use a throw-off and butt system on all that was designed by GMS and machined from brass. The unique nylon lock nut, prevents the throw-off adjusting knob from loosening, keeping GMS' promise to have a system that is simple, trouble-free, and effective. All GMS snare drums feature 20-strand, heat-treated, high-carbon steel snare wire. Hoops on all drums are 2.3mm steel triple flanged. All snare drums have coated Evans G1 tops, and 300-gauge snare bottoms.One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition snare sound.The GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product. GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.For snare with more fl. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Special Edition Snare Drum 5.5X14 Silver/Blue Sparkle Fade.

GMS snare drums use a throw-off and butt system on all that was designed by GMS and machined from brass. The unique nylon lock nut, prevents the throw-off adjusting knob from loosening, keeping GMS' promise to have a system that is simple, trouble-free, and effective. All GMS snare drums feature 20-strand, heat-treated, high-carbon steel snare wire. Hoops on all drums are 2.3mm steel triple flanged. All snare drums have coated Evans G1 tops, and 300-gauge snare bottoms.One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition snare sound.The GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product. GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.For snare with more fl. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS G28 Acrylic Snare Drum 6.5X14 Silver Sparkle With Black.

The G28 Acrylic Snare drum from GMS is to regular snare drums like a formula one racing car is to your average commuter sedan. So it's little surprise that the acrylic shell is decked out with racing stripes. The drum's acrylic shell offers a brighter, louder voice in comparison to wood shell drums. The drum has an excellent crack with a medium-warm resonance.The drum's bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside. The throw-off and butt system was designed to be simple, trouble-free, and effective. The snare drum features 20 strand heat treated high carbon steel snare wire. Hoops are 2.3mm steel triple flanged. GMS acrylic snare drum ships with an Evans coated G1 top, and 300 gauge snare wire.. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 8X10 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS G28 Acrylic Snare Drum 6.5X14 Light Blue With White.

The G28 Acrylic Snare drum from GMS is to regular snare drums like a formula one racing car is to your average commuter sedan. So it's little surprise that the acrylic shell is decked out with racing stripes. The drum's acrylic shell offers a brighter, louder voice in comparison to wood shell drums. The drum has an excellent crack with a medium-warm resonance.The drum's bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside. The throw-off and butt system was designed to be simple, trouble-free, and effective. The snare drum features 20 strand heat treated high carbon steel snare wire. Hoops are 2.3mm steel triple flanged. GMS acrylic snare drum ships with an Evans coated G1 top, and 300 gauge snare wire.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Special Edition Snare Drum 7X13 Chestnut.

GMS snare drums use a throw-off and butt system on all that was designed by GMS and machined from brass. The unique nylon lock nut, prevents the throw-off adjusting knob from loosening, keeping GMS' promise to have a system that is simple, trouble-free, and effective. All GMS snare drums feature 20-strand, heat-treated, high-carbon steel snare wire. Hoops on all drums are 2.3mm steel triple flanged. All snare drums have coated Evans G1 tops, and 300-gauge snare bottoms.One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition snare sound.The GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product. GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.For snare with more fl. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Special Edition Snare Drum 6.5X14 Chestnut.

GMS snare drums use a throw-off and butt system on all that was designed by GMS and machined from brass. The unique nylon lock nut, prevents the throw-off adjusting knob from loosening, keeping GMS' promise to have a system that is simple, trouble-free, and effective. All GMS snare drums feature 20-strand, heat-treated, high-carbon steel snare wire. Hoops on all drums are 2.3mm steel triple flanged. All snare drums have coated Evans G1 tops, and 300-gauge snare bottoms.One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition snare sound.The GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product. GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.For snare with more fl. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 7X8 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 9X12 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Special Edition Snare Drum 5.5X14 Chestnut.

GMS snare drums use a throw-off and butt system on all that was designed by GMS and machined from brass. The unique nylon lock nut, prevents the throw-off adjusting knob from loosening, keeping GMS' promise to have a system that is simple, trouble-free, and effective. All GMS snare drums feature 20-strand, heat-treated, high-carbon steel snare wire. Hoops on all drums are 2.3mm steel triple flanged. All snare drums have coated Evans G1 tops, and 300-gauge snare bottoms.One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition snare sound.The GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product. GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.For snare with more fl. ...details

GMS Drums and Percussion > Acoustic Drums > Bass Drums >

GMS Special Edition Bass Drum 18X20 Silver/Blue Sparkle Fade.

GMS Special Edition bass drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick that it raises the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up one each other. This cross-laminating process creates an even sturdier product. GMS Drum Co. is known for creating ingenious, yet functional products for drummers. They're one of the more innovative drum companies in the market. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug". It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition bass drum sound. They also feature the Evans EQ system.GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a graduated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.Add some high-end boom to your kit, with a GMS Special Edition bass drum. It'll give you a kick like no other.. ...details

GMS Drums and Percussion > Acoustic Drums > Floor Toms >

GMS Special Edition Floor Tom 16X18 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance in all dynamic situations with little to no distortion or necessity for reinforcement hoops, which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product.GMS Drum Co. is known for creating ingenious, yet functional, products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Floor Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell,a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. The toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.As for proper mounting, the Special Edition models employ the GMS Floor Tom Mounting System which spaces all the mounting hardware off the drum shell. With the wider circumference of the leg pattern, the drum shell is able to resonate without the restriction of mounting hardware against it. The mounting brackets themselves are even made at the GMS factory.As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.A lot goes into these GMS Special Edition Toms so you'll get a lot out of them as well. And by that we mean consistent. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 11X14 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 10X13 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Bass Drums >

GMS Special Edition Bass Drum 18X24 Silver/Blue Sparkle Fade.

GMS Special Edition bass drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick that it raises the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up one each other. This cross-laminating process creates an even sturdier product. GMS Drum Co. is known for creating ingenious, yet functional products for drummers. They're one of the more innovative drum companies in the market. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug". It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition bass drum sound. They also feature the Evans EQ system.GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a graduated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.Add some high-end boom to your kit, with a GMS Special Edition bass drum. It'll give you a kick like no other.. ...details

GMS Drums and Percussion > Acoustic Drums > Bass Drums >

GMS Special Edition Bass Drum 18X22 Silver/Blue Sparkle Fade.

GMS Special Edition bass drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick that it raises the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up one each other. This cross-laminating process creates an even sturdier product. GMS Drum Co. is known for creating ingenious, yet functional products for drummers. They're one of the more innovative drum companies in the market. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug". It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition bass drum sound. They also feature the Evans EQ system.GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a graduated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.Add some high-end boom to your kit, with a GMS Special Edition bass drum. It'll give you a kick like no other.. ...details

GMS Drums and Percussion > Acoustic Drums > Floor Toms >

GMS Special Edition Floor Tom 14X14 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance in all dynamic situations with little to no distortion or necessity for reinforcement hoops, which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product.GMS Drum Co. is known for creating ingenious, yet functional, products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Floor Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell,a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. The toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.As for proper mounting, the Special Edition models employ the GMS Floor Tom Mounting System which spaces all the mounting hardware off the drum shell. With the wider circumference of the leg pattern, the drum shell is able to resonate without the restriction of mounting hardware against it. The mounting brackets themselves are even made at the GMS factory.As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.A lot goes into these GMS Special Edition Toms so you'll get a lot out of them as well. And by that we mean consistent. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 8X10 Chestnut.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 7X8 Chestnut.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Bass Drums >

GMS Special Edition Bass Drum 18X20 Chestnut.

GMS Special Edition bass drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick that it raises the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up one each other. This cross-laminating process creates an even sturdier product. GMS Drum Co. is known for creating ingenious, yet functional products for drummers. They're one of the more innovative drum companies in the market. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug". It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition bass drum sound. They also feature the Evans EQ system.GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a graduated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.Add some high-end boom to your kit, with a GMS Special Edition bass drum. It'll give you a kick like no other.. ...details

GMS Drums and Percussion > Acoustic Drums > Bass Drums >

GMS Special Edition Bass Drum 18X24 Chestnut.

GMS Special Edition bass drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick that it raises the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up one each other. This cross-laminating process creates an even sturdier product. GMS Drum Co. is known for creating ingenious, yet functional products for drummers. They're one of the more innovative drum companies in the market. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug". It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition bass drum sound. They also feature the Evans EQ system.GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a graduated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.Add some high-end boom to your kit, with a GMS Special Edition bass drum. It'll give you a kick like no other.. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 9X12 Chestnut.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 11X14 Chestnut.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Bass Drums >

GMS Special Edition Bass Drum 18X22 Chestnut.

GMS Special Edition bass drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick that it raises the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up one each other. This cross-laminating process creates an even sturdier product. GMS Drum Co. is known for creating ingenious, yet functional products for drummers. They're one of the more innovative drum companies in the market. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug". It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality of these Special Edition bass drum sound. They also feature the Evans EQ system.GMS bearing edges utilize a 45-degree cut on the inside of the shell and a shallow 45-degree counter cut on the outside, a graduated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.Add some high-end boom to your kit, with a GMS Special Edition bass drum. It'll give you a kick like no other.. ...details

GMS Drums and Percussion > Acoustic Drums > Mounted Toms >

GMS Special Edition Rack Tom 10X13 Chestnut.

GMS Special Edition drums are made up of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance, providing good vibrations in all dynamic situations with little to no distortion or necessity for reinforcement hoops which can cause problems with resonance. The drum shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier drum. One of the more innovative drum companies in the market, GMS Drum Co., is known for creating ingenious, yet functional products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Rack Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell, a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. All toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.The GMS Suspension System is designed to securely mount your toms, and give you maximum resonance at the same time. The system secures itself to two tension rods on the top side and stabilizes itself with a clip on the bottom hoop. The rubber bumper mounted bottom clip housing, lets the drum "hang", so it will not choke the drum with rigidity. The profile of the mount is very sleek, making it almost invisible to the eye. The actual tom bracket that is on the mount, is a solid piece, exclusive to GMS. These drums go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mi. ...details

GMS Drums and Percussion > Acoustic Drums > Floor Toms >

GMS Special Edition Floor Tom 16X16 Silver/Blue Sparkle Fade.

GMS Special Edition drums are made of select 8-ply North American maple with no gradation in the thickness of the shell as the diameter gets larger. After extensive research, GMS decided the thicker shells give the best performance in all dynamic situations with little to no distortion or necessity for reinforcement hoops, which can cause problems with resonance. The shells they came up with are thin enough to give you wide tonal ranges, strong enough to not need reinforcement hoops, but not so thick as to raise the frequency to a higher pitch. Another unique aspect of their construction is the staggering in the seam construction so none of the ply seams line up with each other. This cross-laminating process creates an even sturdier product.GMS Drum Co. is known for creating ingenious, yet functional, products for drummers. Knowing many drummers prefer the split-lug look and to see more of the shell's finish, they developed the "SE" (Special Edition) lug. Despite its very small footprint, it provides the same musical quality and resonance of its larger predecessor, the "Grand Master lug." It also has the same swivel nut as the "GM" lug, but diverts shell stress, by tensioning from the bottom of the lug casing, as opposed to the top. This makes it visually appealing while also contributing to the quality sound of these Special Edition Floor Toms.GMS bearing edges utilize a 45-degree cut on the inside of the shell,a shallow 45-degree counter cut on the outside, and a gradated bearing edge around the set. In essence, the edges are sharper on smaller-diameter toms and get rounder as the diameter gets larger. This exclusive process enhances the drums' attack and sustain, while offering larger drums more low end and punch. The toms feature Evans coated G1 top, and G1 clear bottoms with hoops that are 2.3mm steel triple flanged.As for proper mounting, the Special Edition models employ the GMS Floor Tom Mounting System which spaces all the mounting hardware off the drum shell. With the wider circumference of the leg pattern, the drum shell is able to resonate without the restriction of mounting hardware against it. The mounting brackets themselves are even made at the GMS factory.As you can see in the pictures, these aren't just well-built drums, but visual beauties as well. To get there, they go through an intense process that starts with hand sanding of the raw shell to give the paint a better surface to which to adhere. They're then primed with a clear primer. They get sanded again until they are flat and even and ready for the paint. After they dry for 10-14 days, they are sanded with no fewer than 6 grades of sandpaper. As soon as they are deemed smooth as glass, they are sent to be buffed by two grades of imported European compounds. The end result is an unmatched mirror-like finish.A lot goes into these GMS Special Edition Toms so you'll get a lot out of them as well. And by that we mean consistent. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Freddie Holiday Signature SE Snare Drum Cobalt Blue 5.5X14.

The GMS Freddie Holliday Signature Snare Drum features an eye-catching 14" x 5" candy apple cobalt blue aluminum shell, with gold-finish die-cast hoops. It also features ten gold-finish Special Edition series snare lugs, the renowned GMS machined snare throw off, ultra-precise stainless steel tension rods, machined stainless steel receivers and Freddie Holliday's signature badge.After countless world tours and studio sessions with renowned R&B/pop singing group Boyz II Men and Rock and Roll Hall of Fame legends, the O'Jays, to name a few, it's easy to see why Freddie Holliday knows a few things about getting a great sound. This is what led the GMS development team to collaborate with Freddie to create the Freddie Holliday Signature Snare Drum.This snare's aluminum drum shell produces a sound that is warmer and more full-bodied than steel, yet it produces all the projection, volume, and crack you can handle, making it the perfect compromise between wood and steel. GMS brings their excellent craftsmanship to this very special drum that will be enjoyed by all drummers seeking that true R&B sound.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS CL Series Snare Drum 7x13 Cherry.

The GMS snare drum from the CL Series features a 7-ply 100% rock maple shell with precision-cut 45° bearing edges. It also features 2.3mm triple-flange hoops, low-mass lugs, and comes equipped with Evans heads.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS CL Series Snare Drum 7x13 Honey Maple.

The GMS snare drum from the CL Series features a 7-ply 100% rock maple shell with precision-cut 45° bearing edges. It also features 2.3mm triple-flange hoops, low-mass lugs, and comes equipped with Evans heads.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 7X13 Natural Maple.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 6.5X14 Natural Maple.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 5.5x14 Natural Maple.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 7X13 Midnight Black.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 7X13 Walnut Burst.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 6.5X14 Midnight Black.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 6.5X14 Walnut Burst.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 5.5X14 Midnight Black.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Steel Snare Drum 5.5x14 Walnut Burst.

The GMS Revolution Maple and Steel Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of steel that is sprayed to the inside of the shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The GMS Revolution snare's steel interior is suited for players who desire volume and fullness of sound. The shell feels like wood, but the sound bounces around inside the drum the way it would with a metal snare. This gives you a little more of the "kang" sound that's associated with metal drums.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 7X13 Natural Maple.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 6.5X14 Natural Maple.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 5.5x14 Natural Maple.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 7X13 Ebony.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 7X13 Walnut Burst.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 6.5X14 Ebony.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 6.5X14 Walnut Burst.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 5.5x14 Ebony.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details

GMS Drums and Percussion > Acoustic Drums > Snare Drums >

GMS Revolution Maple/Brass Snare Drum 5.5x14 Walnut Burst.

The GMS Revolution Maple/Brass Snare Drum offers a unique blend of wood and metal sounds. It features an 8-ply maple shell with a thin layer of brass that is sprayed to the inside of the drum shell. The resonant sound of wood combined with the reflective qualities of metal provides a snare drum with extreme flexibility and versatility. The snare's brass interior gives it a little extra cut, without taking away from the woodiness of the drum. The drum also has outstanding sensitivity and reacts to the lightest of taps. Rimshots are nonabrasive and colorful, reminiscent of Bill Stewart's snare sound. When hit in the center, the GMS snare drum retains some overtones, but produces a rounder sound with great snare response.Equipped with GMS's Special Edition lugs and triple-flange hoops. Bearing edges are left uncoated to promote a warmer tone, while the metal coating amplifies attack, projection, brightness, and bite.. ...details